Page 1 of 2

can not "send" emails

Posted: Wed May 09, 2012 9:15 am
by unclejohnny
Hi
.
I have developed a problem where I can not “send” emails
.
I have Office & Express and the problem is in both
.
I have tried the normal things, Office “detect & repair”, turning off my firewalls, anti-virus etc,
.
If I go into “Accounts” and send a test email, then it works, and I receive the test email in my inbox
.
If I choose “Drafts”, compose an email, then “send”, go to the outbox and “send/receive”, it goes through the motions, but it is not “sent”
.
In Express I get the following messages, in Office, nothing
.
After the send/receive procedure the email it still there, but if I then right click, and “Forward”, a new email window is opened, and I then can send that, but the original email is still in the outbox
.
I have been with Exetel for a long long time, using the same email addresses and have never had a problem
.
Regards Johnno



The connection to the server has failed. Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Port: 25, Secure(SSL): No, Socket Error: 10060, Error Number: 0x800CCC0E
.
The message could not be sent because one of the recipients was rejected by the server. The rejected e-mail address was '(name removed)@exemail.com.au'. Subject 'test', Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Server Response: '550 relay not permitted', Port: 25, Secure(SSL): No, Server Error: 550, Error Number: 0x800CCC79

Re: can not "send" emails

Posted: Wed May 09, 2012 9:42 am
by James
unclejohnny wrote:Hi
.
I have developed a problem where I can not “send” emails
.
I have Office & Express and the problem is in both
.
I have tried the normal things, Office “detect & repair”, turning off my firewalls, anti-virus etc,
.
If I go into “Accounts” and send a test email, then it works, and I receive the test email in my inbox
.
If I choose “Drafts”, compose an email, then “send”, go to the outbox and “send/receive”, it goes through the motions, but it is not “sent”
.
In Express I get the following messages, in Office, nothing
.
After the send/receive procedure the email it still there, but if I then right click, and “Forward”, a new email window is opened, and I then can send that, but the original email is still in the outbox
.
I have been with Exetel for a long long time, using the same email addresses and have never had a problem
.
Regards Johnno



The connection to the server has failed. Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Port: 25, Secure(SSL): No, Socket Error: 10060, Error Number: 0x800CCC0E
.
The message could not be sent because one of the recipients was rejected by the server. The rejected e-mail address was '(name removed)@exemail.com.au'. Subject 'test', Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Server Response: '550 relay not permitted', Port: 25, Secure(SSL): No, Server Error: 550, Error Number: 0x800CCC79
Might be a silly question, but are you usign your Exetel connection to send this email?

Re: can not "send" emails

Posted: Wed May 09, 2012 9:54 am
by unclejohnny
Might be a silly question, but are you usign your Exetel connection to send this email?
.
It was not an email (I assume "usign" was meant to be "using")
.
It is a Forum Post
.
I signed in using my Forum ID and Exetel membership number
.
I am not having any other issues with my machine, I can use Firefox etc, I can also send emails through third party accounts, and also, as stated, I can "Forward" an email

Re: can not "send" emails

Posted: Wed May 09, 2012 10:15 am
by shoner
unclejohnny wrote:Might be a silly question, but are you usign your Exetel connection to send this email?
.
It was not an email (I assume "usign" was meant to be "using")
.
It is a Forum Post
.
I signed in using my Forum ID and Exetel membership number
.
I am not having any other issues with my machine, I can use Firefox etc, I can also send emails through third party accounts, and also, as stated, I can "Forward" an email
Are you using your Exetel internet connection or are on on a different ISP's Internet connection.

If you are using the Exetel internet connection, it should work.
If you are using a different internet connection from another ISP then try using their outgoing SMTP server settings.

Re: can not "send" emails

Posted: Wed May 09, 2012 10:41 am
by unclejohnny
Hi Shoner
.
I only have the one ISP ... Exetel
.

"This will involve selecting the setting "this server requires a secure connection (ssl)" in your mail program"
.
I checked this box and then received another error message

Re: can not "send" emails

Posted: Wed May 09, 2012 10:52 am
by jokiin
unclejohnny wrote:Hi Shoner
.
I only have the one ISP ... Exetel
.

"This will involve selecting the setting "this server requires a secure connection (ssl)" in your mail program"
.
I checked this box and then received another error message
are you using the PC you are having problems sending email from now or are you on another computer at the moment?

Re: can not "send" emails

Posted: Wed May 09, 2012 10:57 am
by unclejohnny
I am on the same computer
.
The problem just seemed to come out of the blue
.
I believe that I have not changed any settings
.
I am on wireless broadband and have been on it for several months

Re: can not "send" emails

Posted: Wed May 09, 2012 11:01 am
by jokiin
unclejohnny wrote:I am on the same computer
.
The problem just seemed to come out of the blue
.
I believe that I have not changed any settings
.
I am on wireless broadband and have been on it for several months
ok I figured you were on a wireless service going by your IP address, are you using the Optus SMTP server settings in your email, what have you got in the SMTP field in your email setup currently?

edit, actually just noticed in your earlier post the error message is the Exetel SMTP, this won't work, you need to use the Optus SMTP settings and mail will work

Re: can not "send" emails

Posted: Wed May 09, 2012 11:09 am
by unclejohnny
pop3.nsw.exemail.com.au
.
mail.optusnet.com.au
.
which are the original settings given to me when the wireless was set up
.
When I do a "Test Account Settings"
.
The five tasks all get a green tick, including .... "send test email message" ... which then sends me this email ... "This is an e-mail message sent automatically by Microsoft Office Outlook's Account Manager while testing the settings for your POP3 account"

Re: can not "send" emails

Posted: Wed May 09, 2012 11:11 am
by jokiin
you need to be using mail.optusnet.com.au as mentioned here http://exewiki.exetel.com.au/index.php? ... N_Settings your error message above does not show this SMTP is being used

Re: can not "send" emails

Posted: Wed May 09, 2012 11:12 am
by jokiin
unclejohnny wrote:pop3.nsw.exemail.com.au
.
mail.optusnet.com.au
.
which are the original settings given to me when the wireless was set up
.
When I do a "Test Account Settings"
.
The five tasks all get a green tick, including .... "send test email message" ... which then sends me this email ... "This is an e-mail message sent automatically by Microsoft Office Outlook's Account Manager while testing the settings for your POP3 account"
ok so it works then, compose a new email and try sending, any error message?

Re: can not "send" emails

Posted: Wed May 09, 2012 11:17 am
by unclejohnny
The "test message" has always worked since i have been testing since the problem occured
.
The only error messages given is when I use Express ... Outlook does not give any error message
.
neither send the email
.
The connection to the server has failed. Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Port: 25, Secure(SSL): No, Socket Error: 10060, Error Number: 0x800CCC0E
.
The message could not be sent because one of the recipients was rejected by the server. The rejected e-mail address was '(name removed)@exemail.com.au'. Subject 'test', Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Server Response: '550 relay not permitted', Port: 25, Secure(SSL): No, Server Error: 550, Error Number: 0x800CCC79

Re: can not "send" emails

Posted: Wed May 09, 2012 11:20 am
by jokiin
unclejohnny wrote:The "test message" has always worked since i have been testing since the problem occured
.
The only error messages given is when I use Express ... Outlook does not give any error message
.
neither send the email
.
The connection to the server has failed. Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Port: 25, Secure(SSL): No, Socket Error: 10060, Error Number: 0x800CCC0E
.
The message could not be sent because one of the recipients was rejected by the server. The rejected e-mail address was '(name removed)@exemail.com.au'. Subject 'test', Account: '(name removed)@exemail.com.au', Server: 'smtp.nsw.exemail.com.au', Protocol: SMTP, Server Response: '550 relay not permitted', Port: 25, Secure(SSL): No, Server Error: 550, Error Number: 0x800CCC79

can you see the problem I've highlighted above?

Re: can not "send" emails

Posted: Wed May 09, 2012 11:42 am
by unclejohnny
As per my post:

Post by unclejohnny on Wed May 09, 2012 12:09 pm
.
pop3.nsw.exemail.com.au
.
mail.optusnet.com.au
.
I have seven email accounts, I have checked, double checked, and they are all
.
pop3.nsw.exemail.com.au
.
mail.optusnet.com.au

Re: can not "send" emails

Posted: Wed May 09, 2012 11:55 am
by jokiin
unclejohnny wrote:As per my post:

Post by unclejohnny on Wed May 09, 2012 12:09 pm
.
pop3.nsw.exemail.com.au
.
mail.optusnet.com.au
.
I have seven email accounts, I have checked, double checked, and they are all
.
pop3.nsw.exemail.com.au
.
mail.optusnet.com.au
yet your error message says otherwise, perhaps you need to delete the accounts and setup from scratch as you definitely have something set wrong